Bugapaluza 14 Engine Give Away Parts Needed!

[Bignick]

Its time for me to start begging for parts again! We turned out a great engine last year thanks to everyone pitching in. Please take a look at these needs and let me know if you have anything that you would be willing to donate or provide at a discounted rate. We did produce a budget with last years engine, so we will buy some new parts this year. Here is a list of what we have vs what we need.


Parts List

• Case-                                   We have a standard/standard case
• Crank-                                  William picked one up in Florida in November. New crank- he needs                                               to be reimbursed.
• Rockers                                Have good rockers
• Cam                                     Have a few options
• Dowel pins                            Have dowel pins
• Rods -                                  have lots of rods- we'll try to get 4 good ones
• Valve covers                         Have covers
• Generator stand                    have a stand
• Oil plate                               have a plate
• Hardware kit                          Have plenty of hardware
• Lifters                                   Have lifters- need to inspect them
  
• Gears (timing, crank and cam)    Have gears
• Fan pulleys                            have the crank, need gen pulley
• Tins                                      Have cylinder tin and behind pulley, need everything else
• Pushrods and tubes-                Have pushrods-need tubes
• Heads-                                   Need heads-Looking to do a SP
• Intake                                  Need intake
• Distributor (and drive)            Need a dist- or need rebuilt
• Carb                                    Need a 30/31 or ? ? ?
• Fan and backing plate             Need Fan- have backing plate
• Gasket kit                             Need to get one (got from Tri-state last year)
• Gland nut                              Need a gland nut
• points, condenser                    will need points and condenser with dizzy
• Flywheel                                Need flywheel or recondition a rusty one
• Generator                              None yet
• Oil pump                               Need to verify
• Oil Cooler                              Need oil cooler
• Main bearings-                       Need (got from Mainly Foreign last year)
• Rod Bearings-                        Need (got from Mainly Foreign last year)
• Cam bearings-                        Need (got from Mainly Foreign last year)
• Doghouse Fan Shroud              Need
• Exhaust valves                       Not yet ($6 each-$24)
• Oil screen                              Not yet ($5)
• Fuel pump                              Not yet ($27)
• Oil pressure switch                   Not yet ($4)
• plugs, wires                            Not Yet ( $10 and $19)
• P/C                                      Do we have some from Jack?
• Coil and bracket                      No coil or bracket ($39, $2.50)

[/list]

[ASBug]

I've got a new shinney coil bracket.
Got a new blue for the bus and it uses a different type.
I'll bring it to the Feb. Cruise in.
KC

[certdubtech]

I am clearing some more junk out, Nick... I don't have much, but will see what I got for your build and let you know.

[ASBug]

I just got in an engine with an 009 and a 34 / 3 Carbie.
I do not plan on using the 009, I'll give it the once over this weekend to make sure it is OK, do you even want an 009?
KC

[Bignick]

I've got a new shinney coil bracket.
Got a new blue for the bus and it uses a different type.
I'll bring it to the Feb. Cruise in.
KC

Sweet! We'll take it!

I am clearing some more junk out, Nick... I don't have much, but will see what I got for your build and let you know.

Ok, just think Single Port with a doghouse cooler!

I just got in an engine with an 009 and a 34 / 3 Carbie.
I do not plan on using the 009, I'll give it the once over this weekend to make sure it is OK, do you even want an 009?
KC

We used one last year! We did a 009 with a 30/31(or other SP carb) on a DP with an adapter, so yeah, we'll take what we can! I know the 009 won't work with your 34!

[Bignick]

Also, does anyone have a junker tachometer that they no longer need or want? Or what about a weedeater/chainsaw/lawnmower gas tank?

I have made a test stand and I'm wanting to throw a tach on it. For the test stand, I have a battery shut off switch, push button starter button, a toggle switch, two idiot lights. Any other ideas to wire up? Looking to have this thing ready for the giveaway motor to display it on. It currently has 2 wheels and a place to hook up a trailer tongue so we can tow it around the show.

[Ret.Bugtech]

Nick, a 34 carb will not fit on a single port intake

[Bignick]

Nick, a 34 carb will not fit on a single port intake

I understood him to say that he couldn't use the 009 with his 34 so he was donating the distributor and getting a vaccuum one for his 34. I don't think a carb was being offered

[ASBug]

Disto = yes.
Carb = nope.
KC

[74loaf]

I have a lawnmower gas tank.... but you will need to take the whole lawnmower to get it =P
 
its at least a nice newer lawn mower...but I dont need it anymore. Would rather someone take the whole thing. havent started it in about 4 years but its yours if you want it. just gotta come get it.

[attack chicken]

I have a tach that may or may not work you are welcome to. I also have a flywheel and single port heads that will need to be gone through,probably have a 30/31 carb, they may all be 34 pic 3s, Ill have to look. I have single port intakes.

[Bignick]

I have a lawnmower gas tank.... but you will need to take the whole lawnmower to get it =P
 
its at least a nice newer lawn mower...but I dont need it anymore. Would rather someone take the whole thing. havent started it in about 4 years but its yours if you want it. just gotta come get it.

Sweet! Any way you can take a photo of it so I can see if its what I need? Taking a whole lawn mower is a big commitment if its not what I need... but I'll probably take you up on that!

I have a tach that may or may not work you are welcome to. I also have a flywheel and single port heads that will need to be gone through,probably have a 30/31 carb, they may all be 34 pic 3s, Ill have to look. I have single port intakes.

Awesome! Rick coming through on a lot of this stuff again! Is this all at the shop and should I come by sometime to discuss what you have?

[Bignick]

William informed me that his crank was been reallocated to his own engine build...we didn't reimburse him in time to get the new one. But he said Lindy has some that have already been machined for less than half of a new one, so we will look at that or else we will buy a new one (hopefully at cost!).

Parts List

• Case-                                   We have a standard/standard case
• Crank-                                  Still looking for a crank
• Rockers                                Have good rockers
• Cam                                     Have a few options
• Dowel pins                            Have dowel pins
• Rods -                                  have lots of rods- we'll try to get 4 good ones
• Valve covers                         Have covers
• Generator stand                    have a stand
• Oil plate                               have a plate
• Hardware kit                          Have plenty of hardware
• Lifters                                   Have lifters- need to inspect them
  
• Gears (timing, crank and cam)    Have gears
• Fan pulleys                            have the crank, need gen pulley
• Tins                                      Have cylinder tin and behind pulley, need everything else
• Pushrods and tubes-                Have pushrods-need tubes
• Heads-                                   Need heads-Looking to do a SP- R&M
• Intake                                  Need intake-R&M
• Distributor (and drive)            Need a dist- or need rebuilt- KC
• Carb                                    Need a 30/31 or ? ? ? - Maybe R&M
• Fan and backing plate             Need Fan- have backing plate
• Gasket kit                             Need to get one (got from Tri-state last year)
• Gland nut                              Need a gland nut
• points, condenser                    will need points and condenser with dizzy
• Flywheel                                Need flywheel or recondition a rusty one
• Generator                              None yet
• Oil pump                               Need to verify
• Oil Cooler                              Need oil cooler
• Main bearings-                       Need (got from Mainly Foreign last year)
• Rod Bearings-                        Need (got from Mainly Foreign last year)
• Cam bearings-                        Need (got from Mainly Foreign last year)
• Doghouse Fan Shroud              Need
• Exhaust valves                       Not yet ($6 each-$24)
• Oil screen                              Not yet ($5)
• Fuel pump                              Not yet ($27)
• Oil pressure switch                   Not yet ($4)
• plugs, wires                            Not Yet ( $10 and $19)
• P/C                                      Need pistons and cylinders
• Coil and bracket                      No coil or bracket-KC (Bracket only) ($39, $2.50)

[/list]
[/quote]

[attack chicken]

Everything is at the shop, come on by with a truck and pick it up anytime!

[attack chicken]

OK, I checked today and I do have a good clean 30/31 carb that just needs to be gone through. Has a dead accelerator pump and will overfill the bowl sometimes, otherwise looks great.
several flywheels to pick from, all will need to be resurfaced
used gland nut
several oil coolers to pick from
several single port intakes
couple sets of single port heads
tacho
I do have some cranks too but no idea if they are junk, may be good for resurface or cores